looking for suitable laboratory equipment?

Our professionals are available 24*7. You can call us any time.

To understanding
Rotary Evaporator To Remove Solvent

Rotary Evaporator To Remove Solvent

A rotary evaporator (or rotavap/rotovap) is a device used in chemical laboratories for the efficient and gentle removal of solvents from samples by evaporation.. The purpose of distillation is to separate a given mixture into its components based on their respective volatilities, through the process of evaporation and condensation (liquid-gas-liquid).

More Product
Year 2007: ORGLIST: Removal of DMF. - geocities.ws

Year 2007: ORGLIST: Removal of DMF. - geocities.ws

Can anyone recommend an effective way of removing DMF from a crude reaction mixture? We have tried evaporation at high temperatures and low pressure using a rotovap to no avail. Any suggestions would be greatly appreciated. Thanks in advance, Christopher Luus. _____ ORGLIST - Organic Chemistry Mailing List

More Product
rotovap dimethyformamide dmf

rotovap dimethyformamide dmf

DMF 6 x 10 mL 40 C 70 min Ethyl Acetate 6 x 10 mL 40 C 12 hrs . Benefits of Using the Centrifan Personal Evaporator vs. Rotovap Problem Solution Reducing Operator Time for Rotary Evaporators . acetate n-Propanol Tetrahydrofuran Chloroform Ethyl acetate Ethanol Dioxane Acetone Methanol Acetonitrile Acetic Acid Dimethylformamide Dimethyl .

More Product
Year 2007: Re: ORGLIST: Removal of DMF

Year 2007: Re: ORGLIST: Removal of DMF

DMF can be removed with a rotovap, if the following precautions are taken: (a) the seal around the rotating shaft must be checked and freshly sealed with good quality vacuum grease; (b) vacuum must be from a mechanical pump in good condition, pulling 0.5 mmHg; (c) the rotating flask must be heated to over 100 deg C; (d) the receiver must be ...

More Product
How Does a Rotovap Work? - Lab Instruments - Lanphan

How Does a Rotovap Work? - Lab Instruments - Lanphan

Jan 18, 2017 When operating a rotovap, following tips should be remembered. To remove algae gunk from the inside of a coiled water condenser, the condenser has to be removed from the rotovap and the coil is soaked in a dilute nitric acid solution for a few hours. After carefully rinsing the insides, the rotovap is reassembled.

More Product
Rotovap Distillation: What Is A Rotary Evaporator? BVV

Rotovap Distillation: What Is A Rotary Evaporator? BVV

Jul 21, 2017 Understanding Rotovap Distillation. Before learning about rotovap setup and operation, you must have a clear picture of the physical change happening inside of the rotary evaporator. Consider how a mixture containing extract and ethanol must first be separated before rotovap distillation can occur.

More Product
How to Minimize Bumping and Foaming Blog

How to Minimize Bumping and Foaming Blog

Jun 26, 2017 For bumping you can add agents, such as boiling chips, which make the boiling more uniform. To prevent contamination and sample loss from bumping or foaming, a bump trap or a foam brake can be installed. This secondary flask will collect your sample if it bumps or foams over, avoiding product loss and a contaminated rotovap.

More Product
Rotary Evaporator (Rotovap) Issues and the Smart Solution

Rotary Evaporator (Rotovap) Issues and the Smart Solution

Mar 11, 2019 Small Sample Sizes (Painstaking vs. Painless) Working with rotary evaporators can be difficult, especially with small samples. Transferring the solvent to the rotovap, followed by painstakingly scraping the sample from the round-bottom flask, not only leads to wasted effort, lost time and loss of sample, but also presents risk of cross-contamination.

More Product
Help removing DMF - ECHEMI

Help removing DMF - ECHEMI

Mar 28, 2022 Aqueous workup with 5% LiCl can help a lot too to remove the last bits of DMF; extract with chloroform, chloroform/isopropanol, or EtOAc. But I recommend speedvac most. …

More Product
Putting the Rule of 20 Into Practice Blog -

Putting the Rule of 20 Into Practice Blog -

May 08, 2020 In general, your bath temperature should be 20C higher than the boiling point of the substance you want to evaporate. And your coolant should be 20C or more lower than the vapor temperature. For example, if the boiling point of your substance is 40C, a bath temperature of 60C and coolant temperature of 20C should provide an optimal setup.

More Product
Year 2007: Re: ORGLIST: Removal of DMF. - geocities.ws

Year 2007: Re: ORGLIST: Removal of DMF. - geocities.ws

Subject: ORGLIST: Removal of DMF. Can anyone recommend an effective way of removing DMF from a crude reaction mixture? We have tried evaporation at high temperatures and low pressure using a rotovap to no avail. Any suggestions would be greatly appreciated. Thanks in advance, Christopher Luus.

More Product
How Rotovap Using

How Rotovap Using

The purpose of using the rotary evaporator. We use the rotary evaporator (rotovap) for two main purposes: 1.to concentrate non-volatile components in a mixture (for example, concentrating the purest and freshest flavors from a blood orange by removing the water); Get Details

More Product
Operation of the Rotary Evaporator (Rotovap)

Operation of the Rotary Evaporator (Rotovap)

The rotovap itself consists of the following parts: a) a long condenser containing a distillation tube surrounded by a coil of glass tubing. This glass tubing will have cold water running through it to provide a cooling atmosphere for the gas as it is being distilled. ... DO NOT REMOVE the flask by pulling straight downwards; this can result in ...

More Product
How does rotary evaporation work? -

How does rotary evaporation work? -

The rotovap works by increasing the rate of evaporation of the solvent by (1) reducing the pressure to lower the solvent boiling point, (2) rotating the sample to increase the effective surface area and (3) heating the solution. ... This usually does the trick for removing DMF, especially when used in conjunction with drying on a manifold ...

More Product
How to get rid of DMF from the organic layer

How to get rid of DMF from the organic layer

•Found online: remove most of DMF. Azeotrope strategy: add toluene(or pentane/hexane/heptane) and evaporate (several times could be needed). Evaporate with …

More Product
Latest News
X

CONTACT US

If you are interested in our products, please contact us, your satisfaction is our eternal pursuit!